Computer Science Homework Help
Computer Science Homework Help. New England College A Network in Cisco Packet Tracer Exercise
Objective:
- Assign appropriate IP Subnet to each network for the supernet 172.16.0.0/16 and fill up following table
- Configure the following topology on packet tracer
- Allow console from PC10 to router R4.
- Assign appropriate IP Subnet to each network for the supernet 172.16.0.0/16 and fill up following table
- Configure the following topology on packet tracer
- Allow console from PC10 to router R4.
- Set banner on every device “UNAUTHORIZED LOGINS ARE PROHIBITED”
- Set credentials (username: cisco & password: cisco) on telnet and console.
- Configure all switches except LAN1 and LAN2 with Ports
- Set banner on every device “UNAUTHORIZED LOGINS ARE PROHIBITED”
- Set credentials (username: cisco & password: cisco) on telnet and console.
- Configure all switches except LAN1 and LAN2 with Ports
- fa1 – 2 for VLAN10
- fa3 – 4 for VLAN11
- fa1 – 2 for VLAN10
- fa3 – 4 for VLAN11
- fa5 – 6 for VLAN20
- fa7 – 8 for VLAN21
- fa 9 – 10 for VLAN30
- fa11 – 12 for VLAN31
- fa13 – 14 for VLAN40
- fa5 – 6 for VLAN20
- fa7 – 8 for VLAN21
- fa 9 – 10 for VLAN30
- fa11 – 12 for VLAN31
- fa13 – 14 for VLAN40
- fa15 – 16 for VLAN50
- fa15 – 16 for VLAN50
- Turn off CDP on R9 and R10
- Enable basic port security on all switch ports to prevent attacks.
- Configure root-bridge Make sure
- Turn off CDP on R9 and R10
- Enable basic port security on all switch ports to prevent attacks.
- Configure root-bridge Make sure
- S1 is root bridge for VLAN 11
- S1 is root bridge for VLAN 11
- S2 is root bridge for VLAN 21
- S3 is root bridge for VLAN31
- S2 is root bridge for VLAN 21
- S3 is root bridge for VLAN31
- Configure inter-vlan routing on R2 for VLAN 20,40,50.
- Configure RIP between R6 and R7 and make sure only vlan 10 and 11 are advertised over RIP.
- Configure EIGRP between R4 and R5 and make sure only vlan 30 and 31 are advertised over EIGRP.
- Configure inter-vlan routing on R2 for VLAN 20,40,50.
- Configure RIP between R6 and R7 and make sure only vlan 10 and 11 are advertised over RIP.
- Configure EIGRP between R4 and R5 and make sure only vlan 30 and 31 are advertised over EIGRP.
- Configure OSPF on R1,R2,R3 and R-Central and make sure only vlan 20 and 21 are advertised over OSPF. Avoid R-Central router links to be used for any type of traffic.
- Configure static routing between PC6 & PC7.
- Configure Ether channel between S1, S2 and S3 as mentioned in the diagram.
- Testing at the end of the topology
- Configure OSPF on R1,R2,R3 and R-Central and make sure only vlan 20 and 21 are advertised over OSPF. Avoid R-Central router links to be used for any type of traffic.
- Configure static routing between PC6 & PC7.
- Configure Ether channel between S1, S2 and S3 as mentioned in the diagram.
- Testing at the end of the topology
- vlan 10 and VLAN 11 should ping each other
- vlan 10 and VLAN 11 should ping each other
- vlan 20 and VLAN 21 should ping each other
- vlan 30 and VLAN 31 should ping each other
- vlan 20, 40 & 50 should ping each other.
- vlan 20 and VLAN 21 should ping each other
- vlan 30 and VLAN 31 should ping each other
- vlan 20, 40 & 50 should ping each other.
IP Addressing table
Device Name |
Interface |
IP Address |
Subnet Mask |
Gateway |
Router |
Gi0/0.10 |
192.168.10.1 |
255.255.255.0 |
n/a |
SW-CENTRAL |
VLAN20 |
192.168.20.10 |
255.255.255.0 |
n/a |
PC1-VL10 |
Fa0 |
192.168.10.4 |
255.255.255.0 |
192.168.10.1 |
Objective:
IP Addressing table
Device Name |
Interface |
IP Address |
Subnet Mask |
Gateway |
Router |
Gi0/0.10 |
192.168.10.1 |
255.255.255.0 |
n/a |
SW-CENTRAL |
VLAN20 |
192.168.20.10 |
255.255.255.0 |
n/a |
PC1-VL10 |
Fa0 |
192.168.10.4 |
255.255.255.0 |
192.168.10.1 |
Computer Science Homework Help